1. Home
  2. Products
  3. Filter Assemblies
  4. Hydraulic Filters
  5. Duplex Filters
  6. High pressure Duplex Filter Pi 4700
Product Image
Print Item  

High pressure Duplex Filter Pi 4700

Filtration Group

973-948-0226
Request a Quote

Related Documents:
Spec/Diagram PDF

Item Information:

High performance filters for modern hydraulic systems.  Nominal pressure up to 315/350 bar (4570/4980 psi), nominal size 40 up to 400 according to DIN 24550.

  • Provided for pipe installation
  • Modular system
  • Compact design
  • Minimal pressure drop through optimal flow design
  • Visual/electrical/electronic maintenance indicator
  • Threaded connections
  • Ergonomic switch-over handle with safety lock and pressure compensation
  • Quality filters, easy to service
  • Equipped with highly efficient glass fibre Sm-x/PS filter elements
  • Beta rated elements according to ISO 16889 multipass test
  • Elements with high differential pressure stability and dirt holding capacity
  • NPT- and SAE-connections on request
  • Worldwide distribution

Flow rate/pressure drop curve complete filter

 

y = differential pressure Δp [bar]
x = flow rate V [l/min]
3. Separation grade characteristics 4. Filter performance data

y=beta-value
x=particle size [µm]

determined by multipass tests (ISO 16889)
calibration according to ISO 11171 (NIST)

 tested according to ISO 16889 (multipass test)

 

Sm-x/PS vst-Elemente with
max. Δp 210 bar
Sm-x/PS vst    3     ß5(c)    ≥200
Sm-x/PS vst    6     ß7(c)    ≥200
Sm-x/PS vst    10   ß10(c)   ≥200
Sm-x/PS vst    16   ß15(c)   ≥200
Sm-x/PS vst    25   ß20(c)   ≥200
Values guaranteed up to
20 bar differential pressure
5. Quality assurance
Filtration Group filters and filter elements are produced according to the following international standards:
6. Symbols
7. Order numbers
8. Technical specifications
Design: line mounting filter
Nominal: Pi 47016-47040 315 bar (4480 psi)
Pi 47004-Pi 47010 350 bar (4980 psi)
Test pressure: Pi 47016-47040 410 bar (5830 psi)
Pi 47004-Pi 47010 455 bar (6470 psi)
Temperature range: -10 °C to +120 °C
  (other temperature ranges on request)
Filter head material: St
Filter housing material: St
Sealing material: NBR/PTFE
Maintenance indicator setting: Δp 5 bar ± 10 %
Electrical data of maintenance indicator:  
Maximum voltage: 250 V AC/200 V DC
Maximum current: 1 A
Contact load: 70 W
Type of protection: IP 65 in inserted and
  secured status
Contact: normally open/closed
Cable sleave: M20x1.5
 

The switching function can be changed by turning the electric upper part by 180° (normally closed contact or normally open contact). The state on delivery is a normally closed contact. By inductivity in the direct current circuit the use of suitable protection circuit should be considered. Further maintenance indicator details and designs are available in the maintenance indicator data sheet.

We draw attention to the fact that all values indicated are average values and do not always occur in specific cases of application. Our products are continually being further developed. Values, dimensions and weights can change as a result of this. Our specialized department will be pleased to offer you advice.

We recommend you to contact us concerning applications of our filters in areas governed by the EU Directive 94/9 EC (ATEX 95). The standard version can be used for liquids based on mineral oil (corresponding to the fluids in Group 2 of Directive 97/23 EC Article 9). If you consider to use other fluids please contact us for additional support.

* Subject to technical alteration without prior notice.
9. Dimensions
10. Installation, operating and maintenance instructions
10.1 Filter installation
Install filter in accordance with the identified flow direction. The filter head is provided with threaded holes for mounting the filters. Ascertain that the required underclearance is provided so that the filter element and the filter housing can be removed. Preferably the filter should be installed with the filter housing pointing downwards. The maintenance indicator must be visible.
10.2 Connecting the electrical maintenance indicator The electrical indicator is connected via a 2-pole appliance plug according to DlN EN 175301-803 with poles marked 1 and 2. The electrical section can be inverted to change from normally open to normally closed position or vice versa.
10.3 When should the filter element be replaced?
1. Filters equipped with visual and electrical maintenance indicator: During cold starts, the indicator may give a warning signal. Press the red button of the visual indicator once again only after operating temperature has been reached. If the red button immediately pops up again and/or the electrical signal has not switched off after reaching operating temperature the filter lement must be replaced after the end of the shift.
2. Filters without maintenance indicator: The filter element should be replaced after the trial run or flushing of the system. Afterwards follow instructions of the manufacturer.
3. Please always ensure that you have original Filtration Group spare elements in stock: Disposable elements (Sm-x/PS) cannot be cleaned.
10.4. Element replacement
Note: The maintenance indicator monitors the filter side in operation, which is identified by the position of the switching lever catch. The change-over transfer valve must be switched prior filter servicing. Now the signal of the contamination indicatoris cancelled and the red button can be represed again:
1. Operate and hold pressure equalizing lever located behind switching lever. Pull catch knob and swivel switching lever. Engage the catch on the clear filter side. Place through or drip pan underneath to collect leaving oil.
2.  Loosen vent screw of the filter side not in use by 2 to 3 turns.
3. Unscrew filter housing by turning counter-clockwise. Clean the housing using a suitable cleaning solvent.
4. Remove filter element by pulling down carefully.
5. Check O-ring on the filter housingl for damage. Replace, if necessary.
6. Make sure that the order number on the spare element corresponds to the order number of the filter name-plate. Open the plastic bag and push element over the spigot in the filter head. Now remove plastic bag.
7. Complete installation by screwing on the housing, turning clockwise until it comes to a full stop. Back off the bowl 1/8 to 1/2 turn.
8. To refill the filter chamber, operate only the pressure equalizing lever (leave the switching lever arrested in its catch) long enough for the medium to emerge bubble- free from the vent bore.
9. Tighten vent screw. Check filter for leaks by operating the pressure equalizing lever once again.
11. Spare parts list