1. Home
  2. Products
  3. Filter Assemblies
  4. Hydraulic Filters
  5. Duplex Filters
  6. Low Pressure Duplex Filter Pi 210
Product Image
Print Item  

Low Pressure Duplex Filter Pi 210

Filtration Group

973-948-0226
Request a Quote

Related Documents:
Spec/Diagram PDF

Item Information:

High performance filters for modern hydraulic systems.  Nominal pressure 32/63 bar (460/900 psi), nominal size up to 600.

  • Modular system
  • Compact design
  • Minimal pressure drop through optimal flow design
  • Visual/electrical/electronic maintenance indicator
  • Threaded connections
  • Change over valve on upstream side
  • Ergonomic switch-over handle with safety lock and pressure compensation
  • User-optimized one-hand-operation
  • Equipped with highly efficient glass fibre PS filter elements
  • Beta rated elements according to ISO 16889 multipass test
  • Elements with high differential pressure stability and dirt holding capacity
  • NPT- and SAE-connections on request
  • Worldwide distribution

 

1. Flow rate/pressure drop curve complete filter

y = differential pressure Δp [bar]
x = flow rate V [l/min]
2. Separation grade characteristics 3. Filter performance data

y=beta-value
x=particle size [µm]

determined by multipass tests (ISO 16889)
calibration according to ISO 11171 (NIST)

 tested according to ISO 16889 (multipass test)

 

PS elements with PS vst elements with
max. Δp 20 bar max. Δp 210 bar
PS    3     ß5(c)    ≥200 PS vst    3     ß5(c)    ≥200
PS    6     ß7(c)    ≥200 PS vst    6     ß7(c)    ≥200
PS    10   ß10(c)   ≥200 PS vst    10   ß10(c)   ≥200
PS    25   ß20(c)   ≥200 PS vst    25   ß20(c)   ≥200
Values guaranteed up to
10 bar differential pressure		 Values guaranteed up to
20 bar differential pressure
4. Quality assurance
Filtration Group filters and filter elements are produced according to the following international standards:
5. Symbols
6. Order numbers
7. Technical specifications
Design: line mounting filter
Nominal pressure: Pi 2105 - Pi 2111 10^7 load changes
  63 bar (900 psi)
Pi 2115 - Pi 2160 10^7 load changes
  25 bar (360 psi)
  2x 10^6 load changes
  32 bar (460 psi)
Test pressure: Pi 2105 - Pi 2111 95 bar (1370 psi)
Pi 2115 - Pi 2160 48 bar (690 psi)
Temperature range: -10 °C to +120 °C
  survival temperature -40 C
  (other temperature ranges on request)
Bypass setting: Δp 3.5 bar ± 10
Filter head material: GAL
Filter housing material: AL/St
Sealing material: NBR/AL
Maintenance indicator setting: Δp 2.2 bar ± 10
Electrical data of maintenance indicator:  
Maximum voltage: 250 V AC/200 V DC
Maximum current: 1 A
Contact load: 70 W
Type of protection: IP 65 in inserted and
  secured status
Contact: normally open/closed
Cable sleave: M20x1.5
 

The switching function can be changed by turning the electric upper part by 180° (normally closed contact or normally open contact). The state on delivery is a normally closed contact. By inductivity in the direct current circuit the use of suitable protection circuit should be considered. Further maintenance indicator details and designs are available in the maintenance indicator data sheet.

We draw attention to the fact that all values indicated are average values which do not always occur in specific cases of application. Our products are continually being further developed. Values, dimensions and weights can change as a result of this. Our specialized department will be pleased to offer you advice.

We recommend you to contact us concerning applications of our filters in areas governed by the EU Directive 94/9 EC (ATEX 95). The standard version can be used for liquids based on mineral oil (corresponding to the fluids in Group 2 of Directive 97/23 EC Article 9). If you consider to use other fluids please contact us for additional support.

* Subject to technical alteration without prior notice.
8. Dimensions
9. Installation, operating and maintenance instructions
10.1 Filter installation
When installing the filter make sure that sufficient space is available to remove filter element and filter housing. Preferably the filter should be installed with the filter housing pointing downwards. The maintenance indicator must be visible.
10.2 Connecting the electrical maintenance indicator The electrical indicator is connected via a 2-pole appliance plug according to DlN EN 175301-803 with poles marked 1 and 2. The electrical section can be inverted to change from normally open position to normally closed position or vice versa.
10.3 When should the filter element be replaced?
1. Filters equipped with visual and electrical maintenance indicator: During cold starts, the indicator may give a warning signal. Press the red button of the visual indicator once again only after operating temperature has been reached. lf the red button immediately pops up again and/or the electrical signal has not switched off after reaching operating temperature, the filter element must be replaced after the end of the shift.
2. Please always ensure that you have original Filtration Group spare elements in stock: Disposable elements (PS) cannot be cleaned.
10.4. Element replacement
Note: The maintenance indicator monitors the filter side in operation, which is identified by the position of the switching lever catch. The flow transfer valve must be switched prior to filter servicing. Now the signal of the maintenance indicator is cancelled and the red button can be depressed again.
1. Operate and hold pressure equalizing lever located in the switching lever. Swivel switching lever. Engage the catch. Place through or drip pan underneath to collect leaking oil.
2.  Loosen vent screw of the filter side not in use by 2-3 turns; maximum back out against safety stop.
3. Unscrew filter bowl by rotating same counter clockwise and clean with a suitable medium.
4. Remove filter element with a side-to-side motion.
5. Check o-ring on the filter housing and the spigot for damage. Replace, if necessary.
6. Make sure that the order number on the spare element corresponds to the order number of the filter name-plate. Remove the plastic bag and push element over the spigot in the filter head.
7. Complete installation by screwing on the housing, turning clockwise until it comes to a full stop. Back off the housing 1/8 to 1/2 turn.
8. To refill the filter chamber, operate only the pressure equalizing lever long enough for the medium to emerge bubblefree from the vent bore. Tighten vent screw. Check filter for leaks by operating the pressure equalizing lever once again.
10. Spare parts list